Power Steering - Revised System Pressure Test Procedure
9218chevy02
Number: 90-45-38
Section: 3B
Date: August 1989
Corporate Bulletin No.: 933205
Subject:
POWER STEERING SYSTEM PRESSURE TEST PROCEDURE
Model and Year:
1990 W CAR (LUMINA) WITH 2.5L, AND 3.1L ENGINE
TO: ALL CHEVROLET DEALERS
THIS BULLETIN CANCELS AND SUPERSEDES DEALER SERVICE BULLETIN 90-27-3B, DATED AUGUST 1989. IT IS BEING REVISED TO CHANGE THE PROCEDURE IN 11b. ALL COPIES OF DEALER SERVICE BULLETIN 90-27-3B SHOULD BE DISCARDED.
This power steering pressure test procedure replaces the procedure found in the 1990 Lumina Service Manual on pages 3-11 and 3-14.
POWER STEERING SYSTEM TEST PROCEDURE:
3.1L Engine
Figure 1
Tools Required:
J 5176-D Power Steering Pressure Tester
J 5176-30 Hose Assembly
J 25323-A Power Steering System Analyzer
J 38049-2 Tube Assembly
J 38049-3 Tubs Nut
1. Remove fuse block shield.
2. Remove A.I.R. pump belt (manual transaxle only).
3. Remove serpentine belt from power steering pump pulley.
4. Remove retaining clip from high pressure pipe.
5. Remove high presure pipe from pump.
- Place a drain pan under vehicle to catch any fluid that may drain.
6. Position high pressure pipe towards right strut.
7. Install serpentine belt.
8. Install J 5176-D as shown in Figure 1.
9. Open the valve on J 5176-D.
10. Start engine and allow system to reach operating temperature. Stop engine and check fluid level, adding fluid if required. When system is at normal operating temperature, the pressure reading on the gage (valve open) should be under 1034 kPa (150 psi). If this pressure is above 1034 kPa (150 psi) stop engine, check the hoses for restriction.
11. Start the engine and let it idle. Fully close the valve 3 times. (Do not leave the valve fully closed for more than 5 seconds, as the pump could be damaged.) Record the highest pressure attained each time the valve is closed. Each reading should show at least 8,619 kPa (1,250 psi). The three readings should be within 345 kPa (50 psi) of each other.
a. If the pressure readings are high enough (at least 8,619 kPa or 1,250 psi) and are within 345 kPa (50 psi) of each other, the pump is functioning properly.
b. If the pressure readings are high enough, but are not within 345 kPa (50 psi) of each other, the flow control valve in the pump is sticking. Remove the valve; clean it and remove any burrs using crocus cloth or fine hone. If necessary, flush the system.
Notice:
Do not attempt to disassemble the flow control valve.
c. If the pressure readings are less than 8,619 kPa (1,250 psi), replace the flow control valve and recheck. If the pressures are still low, inspect the rotor and vanes and replace if necessary.
12. Shut off engine and remove J 5176-D.
13. Partially remove serpentine belt.
14. Install high pressure pipe to pump and close retaining clip to high pressure pipe.
15. Install serpentine belt to power steering pump pulley.
16. Install A.I.R. pump belt (manual transaxle only).
17. Install fuse block shield.
18. Bleed system and check fluid level.
2.5L ENGINE
Figure 2
Tools Required:
J 5176-D Power Steering Pressure Tester
J 5176-30 Hose Assembly
J 25323-A Power Steering System Analyzer
J 38049-1 Hose Assembly
J 38049-25 Tube Assembly
J 38049-3 Tube Nut
1. Raise vehicle, refer to GENERAL INFORMATION (SECTION 0A).
2. Remove pressure pipe from pump.
- Place a drain pan under vehicle to catch any fluid that may drain.
3. Install J 38049-25 to pump and to J 5176-30.
4. Lower vehicle, partially.
5. Install J 51276-D as shown in Figure 2.
6. Open the valve on J 5176-D or J 25323.
7. Start engine and allow system to reach operating temperature.
8. Start the engine and let it idle. Fully close the valve 3 times. (Do not leave the valve fully closed for more than 5 seconds, as the pump could be damaged.) Record the highest pressure attained each time the valve is closed. Each reading should show at least 8,619 kPa (1,250 psi). The three readings should be within 345 kPa (50 psi) of each other.
a. If the pressure readings are high enough (at least 8,619 kPa or 1,250 psi) and are within 345 kPa (50 psi) of each other, the pump is functioning properly.
b. If the pressure readings are high enough, but we not within 345 kPa (50 psi) of each other, the flow control valve in the pump is sticking. Remove the valve; clean it and remove any burrs using crocus cloth or fine hone. If the system appears to be contaminated, flush it. If it is exceptionally dirty, both the pump and rack and pinion gear must be completely disassembled, cleaned and reassembled.
c. If the pressure readings are less than 8,619 kPa (1,250 psi), replace the flow control valve and recheck. If the pressures are still low, inspect the rotor and vanes and replace if necessary.
9. Shut-off engine and remove J 5176-D.
10. Raise vehicle, refer to GENERAL INFORMATION (SECTION 0A).
11. Install high pressure pipe to pump.
12. Lower vehicle.
13. Bleed system and check fluid level.