Camshaft: Service and Repair
REMOVAL
1. Disconnect negative cable at battery.
2. Drain engine oil.
3. Drain coolant.
4. Remove oil pan.
5. Remove cylinder head cover.
6. Remove timing chain cover.
7. Remove 2nd timing chain.
8. Remove CMP sensor.
9. To secure work in the following steps, reinstall mounting member, engine front torque bush, rear mounting and rear mounting No.2 bracket.
10. Set key on crankshaft in position as shown by turning crankshaft. This is to prevent interference between valves and piston.
11. Loosen camshaft housing bolts in such order as indicated in figure and remove them.
12. Remove camshaft housings.
13. Remove camshafts.
14. Remove valve lash adjusters.
NOTE:
^ Never disassemble hydraulic valve lash adjuster.
^ Don't apply force to body of adjuster, oil in high pressure chamber In adjuster will leak.
^ Immerse removed adjuster in clean engine oil and keep it there till reinstalling it so as to prevent oil leakage. If it is left in air, place it with its bucket body facing down. Don't place on its side or with bucket body facing up.
INSPECTION
Cam Wear
Using a micrometer, measure cam height. If measured height is below its limit, replace camshaft.
Camshaft Runout
Set camshaft between two "V" blocks, and measure its runout by using a dial gauge.
If measured runout exceeds below specified limit, replace camshaft.
Runout Limit: 0.10 mm (0.0039 inch)
Camshaft Journal Wear
Check camshaft journals and camshaft housings for pitting, scratches, wear or damage.
If any malcondition is found, replace camshaft or cylinder head with housing. Never replace cylinder head without replacing housings.
Check clearance by using gaging plastic. Checking procedure is as follows.
1. Clean housings and camshaft journals.
2. Make sure that all valve lash adjusters are removed and install camshaft to cylinder head.
3. Place a piece of gaging plastic to full width of journal of camshaft (parallel to camshaft).
4. Install camshaft housing.
5. Tighten camshaft housing bolts in such order as indicated in figure a little at a time till they are tightened to specified torque.
NOTE: Do not rotate camshaft while gaging plastic is installed.
Tightening Torque (a): 11 Nm (1.1 kg-m, 8.0 ft. lbs.)
6. Remove housing, and using scale on gaging plastic envelop, measure gaging plastic width at its widest point.
If measured camshaft journal clearance exceeds limit, measure journal (housing) bore and outside diameter of camshaft journal. Replace camshaft or cylinder head assembly whichever the difference from specification is greater.
Wear of Hydraulic Valve Lash Adjuster
Check adjuster for pitting, scratches, or damage. If any malcondition is found, replace.
Measure cylinder head bore and adjuster outside diameter to determine cylinder head-to-adjuster clearance. If clearance exceeds limit, replace adjuster or cylinder head.
Oil Relief Valve
Check oil relief valve for clogging and ball for being stuck.
INSTALLATION
1. Before installing valve lash adjuster to cylinder head, fill oil passage of cylinder head with engine oil according to following procedure.
Pour engine oil through oil holes and check that oil comes out from oil holes in sliding part of valve lash adjuster. Perform this check on both intake and exhaust sides.
2. Install valve lash adjusters to cylinder head.
Apply engine oil around valve lash adjuster and then install it to cylinder head.
3. Match match mark on crank timing sprocket and mating surface of cylinder block and lower crankcase.
4. Install camshafts.
Apply oil to sliding surface of each camshaft and camshaft journal then install them by aligning match marks on cylinder head and camshafts as shown in figure.
NOTE: Install camshaft in such direction that its end with groove for CMP sensor installation comes to exhaust side.
5. Install camshaft housing pins as shown in figure.
6. Apply sealant "A" to exhaust camshaft end housing sealing surface area as shown in figure.
"A": Sealant 99000-31150
7. Check position of camshaft housings.
Embossed marks are provided on each camshaft housing, indicating position and direction for installation. Install housings as indicated by these marks.
8. After applying oil to housing bolts, tighten them temporarily first. Then tighten them by following numerical order in figure. Tighten a little at a time and evenly among bolts and repeat tightening sequence two or three times before they are tightened to specified torque.
Tightening Torque (a): 11 Nm (1.1 kg-m, 8.0 ft. lbs.)
9. Install CMP sensor.
10. Install 2nd timing chain.
11. Install timing chain cover.
12. Install cylinder head cover.
13. Install oil pan.
14. Install cooling system and other parts.
15. Refill cooling system with coolant and engine with engine oil.
16. Check ignition timing and adjust as necessary, referring to Ignition System; Ignition Timing.
17. Check to make sure that there is no coolant leakage and oil leakage at each connection.
CAUTION:
^ Don't turn camshafts or start engine (i.e., valves should not be operated) for about half an hour after reinstalling hydraulic valve lash adjusters and camshafts. As it takes time for valves to settle in place, operating engine within half an hour after their Installation may cause interference to occur between valves themselves or valves and piston.
^ If air is trapped in valve lash adjuster, valve may make tapping sound when engine is operated after valve lash adjuster is installed. In such a case, run engine for about half an hour at about 2,000 r/min., and then air will be purged and tapping sound will cease. Should tapping sound not cease, it is possible that valve lash adjuster is defective. Replace it if defective.
If defective adjuster can't be located by hearing among 16 of them, check as follows.
1. Stop engine and remove cylinder head cover.
2. Push adjuster downward by hand (with less than 20 kg or 44 lbs. force) when cam crest is not on adjuster to be checked and check if clearance exists between cam and adjuster. If it does, adjuster is defective and needs replacement.